For kitchen and vanity cabinets, moisture-resistant (MR or HMR) board is the one to ask for, in MDF or particleboard. On Polytec's own test figures, MR MDF and MR particleboard swell the same and hold screws the same, while standard particleboard swells more and holds less.
Below is what each board is made of, what HMR means, which board goes where in a kitchen, vanity and laundry, how they hold screws, how they cope with humid weather, where plywood fits and what E0 and E1 mean. The figures are the makers' own data sheet results, checked on 16 November 2026. There are no prices here: for those, see our guide to kitchen cabinet costs.
What is the difference between MDF and particleboard?
Particleboard is made from wood chips and resin. MDF (medium density fibreboard) is made from fine wood fibre and resin. That is how board maker Polytec defines them in its glossary. On Polytec's figures, MDF is denser and more than twice as strong in bending.
Here is how Polytec's three melamine-faced boards compare on its own tests:
| Polytec test result | Standard particleboard | MR particleboard | MR MDF |
|---|---|---|---|
| Made from | Wood chip and resin | Wood chip and resin | Wood fibre and resin |
| Thicknesses | 9 to 16 mm | 16 to 33 mm | 9 to 32 mm |
| Density | 650 kg/m3 | 650 kg/m3 | 730 kg/m3 |
| Bending strength (MOR) | 16 MPa | 18 MPa | 40 MPa |
| Thickness swell, 24 hours | 9% | 6% | 6% |
| Screw holding, edge / face | 800 / 600 N | 1,000 / 800 N | 1,000 / 800 N |
| Emission class | E1 | E1 | E0 |
| Polytec says it suits | Low humidity | Low to medium humidity, accidental wetting | Low to medium humidity, accidental wetting |
Source: Polytec technical data sheets for MR particleboard and standard particleboard (May 2026) and melamine MDF (July 2026), tested to AS/NZS 1859.2.
The weight shows up when you carry it. A 16 mm sheet of 2400 x 1200 mm weighs about 33 kg in Polytec's MDF and about 30 kg in its particleboard.
What is HMR board, and is it waterproof?
HMR means high moisture resistant. It is board made with a resin that resists water better, and no, it is not waterproof. Cost guides and quotes often say HMR. The board makers label the same thing MR.
Laminex says its Trade Essentials MR MDF gets its moisture resistance from a "specially formulated moisture resistant resin". It says the board suits high humidity and accidental wetting, for kitchen cupboards, vanities and laundry cupboards, but not outdoor use.
Every maker we checked stops short of waterproof:
- Polytec says its MR MDF doors, like any wood-based panel, "cannot be made totally waterproof".
- Kaboodle says its flat pack cabinets are made with moisture resistant board, "not waterproof".
- Polytec's tests still show MR board swelling 6% in thickness over 24 hours, against 9% for standard board. On a 16 mm panel, that is about 1 mm against about 1.4 mm.
So MR board buys you time, not immunity. A slow leak under a sink will still ruin it. Wipe up spills, fix drips fast and keep the cut edges sealed.
Which board do kitchen and vanity cabinets use?
Most use MR board for the boxes and MR MDF for the doors. The boxes (carcasses) can be MR particleboard or MR MDF. Doors go on MDF because it can be routed and wrapped.
- Boxes. Polytec makes melamine MR particleboard for kitchens, bathrooms, laundries and wardrobes. Sparky's Brisbane cabinetry guide (September 2026) says HMR is the minimum for cabinet boxes in a humid climate.
- Doors. Polytec makes its melamine and vinyl-wrapped doors on E0 MR MDF, and Laminex its melamine, vinyl-wrapped and 2 pac doors. Laminex says MDF can be cut, drilled and routed without chipping or splintering. That is what lets a door take a Shaker profile.
- Vanities. A vanity sits in the wettest room in the house, so MR is a must there. Our guide to bathroom vanity installation cost covers the rest of that job.
- Laundries. The same goes for laundry cupboards near a tub and washing machine. See our laundry renovation cost guide.
Flat pack is no different. Kaboodle's cabinets use moisture resistant board, and our guide to flat pack kitchen installation cost covers fitting them. The brand of the door finish matters less than the board under it. Our guide to Polytec vs Laminex compares the two big brands.
Which board holds screws and hinges better?
On Polytec's figures, MR particleboard and MR MDF hold screws equally well: 1,000 N in the edge and 800 N in the face. Standard particleboard holds 20% less in the edge (800 N) and 25% less in the face (600 N). Hinges and drawer runners are screwed in, so this is the number that matters.
How the screw goes in matters as much as the board. Laminex's guide for its Craftwood MDF says:
- Use parallel threaded screws.
- Go longer: a 25 mm screw has twice the holding power of a 13 mm screw.
- When screwing into an edge, keep the screw no thicker than 20% of the board. For 16 mm board, that is 6 gauge at most.
- Drill pilot holes 2 to 3 mm longer than the screw, at about 80% of the screw's core width.
- Stay at least 25 mm from a corner and 10 mm from an edge. In an edge, never closer than 75 mm to the end of the panel.
- Do not over-tighten. Turning a tight screw further weakens its hold.
How do these boards cope with Gold Coast humidity?
MR board copes. Standard particleboard does not hold up well. We found no Gold Coast guide, so this is from Sparky's Brisbane page (September 2026), the closest match:
- Brisbane's average humidity is 60 to 80%, the highest of any capital city, Sparky says.
- Standard particleboard will "swell at joins and around the sink within 2-3 years".
- HMR board is the minimum for cabinet boxes.
- Cabinetry should meet AS 4386, the domestic kitchen standard. Polytec's warranty also asks for installs to that standard.
Polytec rates standard particleboard for low humidity only, and its MR boards for low to medium humidity. Sparky says the joins and the sink cupboard are where standard board fails first. So if you only upgrade one cupboard, make it the one under the sink.
Where does plywood fit?
Plywood is an upgrade some cabinet makers use for the boxes, at a higher price. Sparky's Brisbane guide says some premium builds use marine-grade plywood for extra moisture resistance, at about 20 to 30% more than HMR.
Laminex's Trade Essentials plywood brochure lists cabinets, kickboards and joinery among its uses, and adds some catches:
- Exposed plywood must be sealed or finished, or the face veneer can crack (checking) as it takes in and lets out moisture.
- Marine plywood is made to the British standard BS 1088. Laminex says its marine species are not naturally durable, so they need preservative treatment outdoors.
- Plywood is real timber, so its colour changes in light. Laminex says as little as an hour of sun can change it.
Sparky treats HMR as the baseline and plywood as the upgrade. Laminex also points out that some plywood edges can be left on show as a design feature, which board cannot do.
What do E0 and E1 mean on a board?
They are limits on how much formaldehyde a board gives off. E0 is the lower one. An EWPAA certificate on Polytec's site sets the limits for fibreboard tested to AS/NZS 1859.2:
| Class | Formaldehyde limit | Note |
|---|---|---|
| Super E0 | Average 0.3 mg/L or less | An industry limit, not in the standard |
| E0 | 0.5 mg/L | Polytec MR MDF and Laminex door MDF are E0 |
| E1 | 1.0 mg/L | Polytec MR particleboard is E1 |
Source: EWPAA formaldehyde emission classifications (Engineered Wood Products Association of Australasia, issued 24 May 2018).
The made-to-measure doors from both big brands are E0. Laminex says all its Trade Essentials MDF is made in Gympie, Queensland, at E0. If low emissions matter to you, ask for E0 in writing on the quote, for the boxes as well as the doors.
In Queensland, kitchen and cabinet work valued over $3,300 needs a QBCC licensed contractor. We fit kitchens, vanities and laundry cupboards across the Gold Coast, flat pack and custom. We book the licensed trades and give a timeline with the proposal. See our kitchen renovation page for what we do, or try our free kitchen renovation cost calculator.
Where do these figures come from?
Checked on 16 November 2026: Polytec's glossary (undated) and technical data sheets for LPM MR particleboard (May 2026), LPM standard particleboard (May 2026), LPM MDF (July 2026) and thermolaminated doors (May 2026), its melamine doors care guide (March 2026) and the EWPAA formaldehyde certificate it hosts (24 May 2018). Laminex's Trade Essentials MDF Raw and Plywood brochures (undated) and its Made-to-Measure Doors and Panels brochure (November 2026). Kaboodle's FAQ (undated). Sparky, kitchen cabinetry cost Brisbane (updated September 2026). The QBCC page on when you need a licence (reviewed August 2021). Test figures are each maker's own. We will check these figures again every three months.
See our kitchen renovations work, or check what your job will cost.



