Skip to content

What Do the Wind Ratings N1, N2, N3 and N4 Mean?

N1 to N4 explained, how to find yours and what it changes.

Brett FieldOwner, Field Carpentry8 min read
Covered timber deck with an outdoor dining setting

A wind rating (the proper name is wind classification) tells everyone who builds a house how strong a wind it must be designed to handle. N1 is the lowest class and N6 the highest outside the cyclone areas, so an N3 home is built for stronger gusts than an N2 home: 50 m/s against 40 m/s, according to Lysaght's wind classification guide.

Below is what each class means, how a site's class is worked out, how to find yours, what Queensland sources say about the Gold Coast, and what the class changes in a build or renovation. Every figure comes from makers' guides and Queensland Government reports, checked on 16 November 2026. It is a guide, not a rating for your home.

What does a wind rating like N2 or N3 mean?

It is the wind class of the house under Australian Standard AS 4055, Wind loads for housing. The class sets the design wind speed, and that decides how strong the frame, roof, fixings, windows and doors must be.

Lysaght, the BlueScope roofing brand, says AS 4055 sets out 10 classes. N1 to N6 are for non-cyclonic areas. C1 to C4 are for cyclonic areas. The higher the number, the stronger the wind the house is designed for.

The National Construction Code lets a house be designed for wind with AS 4055 or with the general wind standard, AS/NZS 1170.2 (NCC 2022 Housing Provisions, Part 2.2). The quick AS 4055 method has limits. Lysaght says it only suits houses up to 2 storeys, no wider than 16 m and no higher than 8.5 m. The Queensland Reconstruction Authority (QRA) says a home with three storeys, a large floor area or an unusual shape must be designed by an engineer to AS/NZS 1170.2.

So "N3" on your plans is a short way of saying: this house was designed for the gusts an N3 site can get.

What are the wind classes N1 to N6 and C1 to C4?

Each class has a design gust speed. Lysaght lists two for each class: a serviceability speed and a higher ultimate speed. The ultimate speed is the design wind speed the QRA quotes for the C classes.

ClassUsed inServiceability gustUltimate gustUltimate in km/h (our sum)
N1Non-cyclonic areas26 m/s34 m/sabout 122 km/h
N2Non-cyclonic areas26 m/s40 m/sabout 144 km/h
N3Non-cyclonic areas32 m/s50 m/sabout 180 km/h
N4Non-cyclonic areas39 m/s61 m/sabout 220 km/h
N5Non-cyclonic areas47 m/s74 m/sabout 266 km/h
N6Non-cyclonic areas55 m/s86 m/sabout 310 km/h
C1 to C4Cyclonic areas32 to 55 m/s50 to 86 m/sabout 180 to 310 km/h

Source: Lysaght PAB10, Wind classification design guide (August 2025). The km/h column is the m/s figure times 3.6, rounded.

N3 and C1 share the same design wind speed. The difference is the pressure inside the house. A Queensland Government wind hazard report (Queensland Fire and Emergency Services, 2021) says C classes assume a window or door could be broken by flying debris in a cyclone, so the roof has to hold on against higher pressure. It matches N3 to C1, N4 to C2, N5 to C3 and N6 to C4.

How is a home's wind rating worked out?

From four things about the site. Lysaght's guide, based on AS 4055, lists them:

  • Wind region. Where the house is, from the wind region map in AS/NZS 1170.2. Regions A and B are non-cyclonic. Regions C and D are cyclonic.
  • Terrain category. How rough the ground is within 500 m. Open water and flat, treeless land are the most exposed (TC1). Suburbs with at least 10 houses per hectare are TC3.
  • Shielding. Full shielding means no open areas within 100 m and at least two rows of houses around yours. A house facing open parkland, open water or an airfield gets no shielding.
  • Topography. Whether the house sits on a hill, and how high up. Classes run from T0 (flat) to T5 (the top of a cliff).

The four are combined in a table to give the class. More exposure means a higher class. The QRA puts it simply for cyclone areas: "the better the view, the higher the wind classification".

How do I find the wind rating for my address?

Start with your building plans or contract. The QRA says the correct wind classification for your home should be marked on them.

If you cannot find it:

  • Older homes may not have one. The QRA says homes built before the 1990s may not have a wind classification, and that a building professional can assess the site and set one.
  • Ask the right person. The QRA says the class is set by a trained building professional, such as an engineer, builder or building certifier. The QBCC's windows fact sheet asks for a site wind speed assessment to AS 4055 from a professional engineer or other suitably qualified person.
  • Get a rough idea yourself. Lysaght's guide walks through the four steps, but it calls itself "an approximate guide". It does not replace the assessment.

If your renovation needs approval, the certifier will look at the plans, wind class included. Our guide to council approval for renovations on the Gold Coast covers who approves what.

What wind rating are Gold Coast homes?

There is no one rating for the whole city. Each site gets its own. What the sources do say:

  • Region B. The Severe Wind Hazard Assessment for Queensland (2021) puts the City of Gold Coast in Wind Region B, which it calls intermediate. In Queensland, it says Region B runs from south of Bundaberg to the New South Wales border, and homes there must be designed to resist weakened tropical cyclones.
  • N2 or higher. The same report says the minimum standard in Region B is N2 or higher. It adds that a house can be built to the matching C class for extra strength.
  • The range in Region B. In Lysaght's table, a Region B house runs from N2 to N6. A flat suburban block with houses all around is N2. A house on flat ground facing open water, with no shielding, is N4. Lysaght's own example puts a Brisbane house on top of a steep hill at N5.

One more thing. The 2021 report refers to the 2011 edition of the wind standard. Lysaght's 2025 map shows Region B split into B1 and B2. Your engineer or certifier works out which applies to your block.

What does the wind rating change in a build or renovation?

Almost everything that holds the house together. A higher class means stronger fixings, closer framing or bigger members.

  • Tie-downs and connections. The QRA says connections and details must be chosen for the correct wind class. Before a new roof goes on, it says to check that the tie-downs suit the home's wind class and upgrade them if needed.
  • Tile to metal. The QRA says sheet metal roofs are lighter than tile, so the uplift is greater, and they need stronger tie-downs.
  • Span tables. Makers write their span tables for set wind classes. Our guide to what a lintel is shows a table written for wind class N2. Our guide to rafter span tables shows one split by wind class.
  • Ceilings. Gyprock's Red Book 2 install guide (May 2020) sets how far apart ceiling framing can be by wind class. For 10 mm Supaceil board it allows 600 mm in N1 to N4, 450 mm in N5 and C1, and 300 mm in C3 and C4.

Re-roofing on the Gold Coast has its own trigger. The City of Gold Coast says roofing work that replaces more than 20% of the existing roof needs building approval.

We build decks and do the framing inside kitchen, bathroom and laundry renovations across the Gold Coast. We build to the wind class on the plans and to the engineer's tie-down details. We do not set the wind class: the engineer or certifier does. Brett holds QBCC licence 15316127. See our carpentry page for the work we do.

Do windows and doors need to match the wind rating?

Yes. The QRA says all windows and garage doors must be rated to the wind classification shown on the plans.

The QBCC fact sheet on windows and glazed external doors (October 2022) says:

  • when you order windows, give the maker the site wind speed assessment to AS 4055
  • windows carry AS 2047 and AS 1288 labels, and those labels must match where each window goes
  • the installer needs the fixing details for the window's size and wind speed

Weak windows matter for the roof too. Metroll's wind guide (September 2020) says the inside pressures used for the N classes only hold if the windows, doors and garage doors are designed to resist the design winds. The Queensland wind report found that when a door or window broke in Cyclone Seroja in Western Australia, the pressure inside jumped, and roofs built for low inside pressure were not strong enough.

The wind class can also limit the window sizes on offer. Our guide to standard window sizes in Australia shows how makers' charts change with the wind load.

Where do these figures come from?

Checked on 16 November 2026: Lysaght, PAB10 Wind classification design guide (August 2025); Metroll (BlueScope), Designing for wind speeds, a guide to wind classification (September 2020); Queensland Fire and Emergency Services, Severe Wind Hazard Assessment for Queensland, Technical Report One (2021); Queensland Reconstruction Authority, Cyclone Resilient Building Guidance for Queensland Homes (December 2019); QBCC, How to identify selection criteria for windows and glazed external doors (fact sheet, effective October 2022); NCC 2022 Housing Provisions, Part 2.2 Structural provisions; Gyprock, The Red Book 2 Residential Installation Guide (May 2020); and City of Gold Coast, Do your building works need approval (undated). AS 4055 and AS/NZS 1170.2 are paid standards: we used the figures as the makers and the Queensland Government publish them. We will check these figures again every three months.

See our carpentry work, or check what your job will cost.

Filed under Carpentry

Free price check

What will your job cost?

3 quick questions, then a Gold Coast price range. No details needed.

Question 1 of 3

What's the job?
Brett Field Free price check