How far a ceiling joist can span depends on its size, its spacing and what it carries, so the answer comes from a maker's span table. In Dindas Australia's free LVL 13.2 table, a 130 x 45 mm ceiling joist at 600 mm spacing spans up to 4,000 mm as a single span.
Below is what ceiling joists do, sample spans and sizes from a maker's table, how far apart they go, what a hanging beam is, what happens when a wall comes out, and when you need an engineer or approval in Queensland. These are published figures from makers' guides, checked on 16 November 2026. They are a guide, not a design for your ceiling.
What does a ceiling joist do?
It holds up the ceiling. Dindas defines a joist as a repeating structural member that supports a floor or a ceiling. The plasterboard is screwed or glued to the joists from below, or to battens fixed across them.
Gyprock, the plasterboard maker, says ceiling linings can be fixed straight to the main timber or steel framing, or to battens and metal furring channels. It says all ceiling framing must be designed for the loads on it, and its ceiling tables allow for up to 5 kg per m2 of insulation on top.
In a truss roof, the bottom chords of the trusses do this job, and the ceiling fixes to them. In a roof framed with rafters, separate ceiling joists span between the walls. The ceiling also helps the rafters: in the Dindas rafter tables, a ceiling attached under the rafters restrains their bottom edge. Our guide to rafter span tables covers the roof side.
How far can a ceiling joist span?
In the rows below, from 2.9 m for a 90 x 45 mm joist up to 9.4 m for a 300 x 45 mm joist running over a middle support. These are sample rows from the Dindas ceiling joist table.
| Dindas LVL 13.2 ceiling joist | Single span, 450 mm spacing | Single span, 600 mm spacing | Continuous, 450 mm spacing | Continuous, 600 mm spacing |
|---|---|---|---|---|
| 90 x 45 mm | 3,100 mm | 2,900 mm | 3,900 mm | 3,400 mm |
| 130 x 45 mm | 4,300 mm | 4,000 mm | 5,500 mm | 4,800 mm |
| 150 x 45 mm | 4,900 mm | 4,600 mm | 6,200 mm | 5,500 mm |
| 200 x 45 mm | 5,900 mm | 5,700 mm | 7,500 mm | 7,100 mm |
| 240 x 45 mm | 6,700 mm | 6,400 mm | 8,400 mm | 8,100 mm |
| 300 x 45 mm | 7,700 mm | 7,400 mm | 9,700 mm | 9,400 mm |
Source: Dindas LVL 13.2 Span Tables Design Guide (2025), ceiling joists, wind classes N1 to N4 and C1 to C3. The table limits sag to the span divided by 400, or 12 mm, and needs at least 70 mm of bearing at each support.
"Continuous" means one joist runs unbroken over a middle support, such as an internal wall. Dindas only counts it as continuous if the shorter span is at least 75% of the longer one. If not, use the single span column.
These are LVL figures. Pine has its own tables: Standards Australia sells the MGP10 framing span tables for wind class N3 as AS 1684.2 Supplement 4. Hyne's free span tables cover floor joists, bearers and lintels, not ceiling joists. Never read a pine size off an LVL table.
What size are ceiling joists in Australian houses?
There is no one standard size. The size is whatever the table gives for the span, the spacing and the product. Using the Dindas table at 600 mm spacing as a single span:
- a 3 m span: a 90 x 45 mm joist reaches 2,900 mm, just short, so the next size up, 130 x 45 mm, is the first that fits
- a 4 m span: 130 x 45 mm reaches exactly 4,000 mm
- a 5 m span: 150 x 45 mm reaches 4,600 mm, so 200 x 45 mm (5,700 mm) is the first that fits
Those spans are measured centre to centre of the supports, so measure the same way. Dindas also makes 63 and 75 mm thick joists, which span a little further at the same depth.
For older homes, the size of the joists already there is on the original plans if you have them. If not, a carpenter can measure them in the roof space, and an engineer or certifier checks them against the table for any change.
How far apart are ceiling joists spaced?
No more than 600 mm under Gyprock plasterboard, and closer for some boards and wind classes. The plasterboard sets the limit. Here is what Gyprock's Red Book 2 install guide (May 2020) allows for interior ceilings:
| Wind class | 10 mm Gyprock Plus or Aquachek | 10 mm Supaceil or Superchek | 13 mm Gyprock Standard or Soundchek |
|---|---|---|---|
| N1 to N4 | 450 mm | 600 mm | 600 mm |
| N5, C1 | 450 mm | 450 mm | 600 mm |
| N6, C2 | 300 mm | 450 mm | 450 mm |
| C3, C4 | 300 mm | 300 mm | 300 mm |
Source: Gyprock, Red Book 2, Table 13, maximum framing centres for interior ceilings, with up to 5 kg per m2 of insulation.
So if the joists are further apart than the board allows, battens or metal furring channels go across them at the right spacing. Gyprock says furring channels also give a steadier fixing and let the ceiling be levelled.
What is a hanging beam?
A hanging beam is a beam that carries ceiling loads. Dindas titles its hanging beam tables "supporting ceiling loads only", and sizes each beam by the width of ceiling it holds up. Here are sample rows, for wind classes N1 to N4:
| Dindas LVL 13.2 hanging beam | Ceiling load width 1,800 mm | 2,400 mm | 3,000 mm | 3,600 mm |
|---|---|---|---|---|
| 150 x 45 mm | 3,600 mm | 3,200 mm | 2,900 mm | 2,700 mm |
| 200 x 45 mm | 4,400 mm | 4,100 mm | 3,800 mm | 3,600 mm |
| 240 x 45 mm | 5,000 mm | 4,600 mm | 4,400 mm | 4,100 mm |
| 300 x 45 mm | 5,900 mm | 5,500 mm | 5,100 mm | 4,900 mm |
Source: Dindas LVL 13.2 guide (2025), hanging beams, maximum spans. It assumes a ceiling mass of 20 kg per m2 and a 30 degree roof pitch, with at least 70 mm bearing at each end. Ceiling load width is how wide a strip of ceiling the beam holds up.
Dindas also has tables for counter beams, which support a hanging beam. Wesbeam lists strutting beams and hanging beams among the roof members its LVL is used for. Which of these your roof has is on the plans. Our guide to LVL beam sizes explains LVL itself.
What happens to the ceiling joists when a wall comes out?
If the joists sit on that wall, they lose their support and need a new one before the wall goes. The new support is a beam, sized by an engineer.
Our guide on how to tell if a wall is load bearing says a wall down the middle of the house is often the one the ceiling joists span onto, and covers the signs and the checks.
Two things to know before you plan it:
- The hanging beam table is for ceiling loads only. If the wall also holds up part of the roof, that is a different load, and the beam is the engineer's call.
- Longer spans need deeper members. Take the wall out of the middle of a 6 m wide room and the joists go from two 3 m spans to one 6 m span. As single spans at 600 mm spacing in the Dindas table, that is the jump from a 130 x 45 mm joist to a 240 x 45 mm one.
Do I need an engineer or approval to change ceiling joists?
Usually, yes. Ceiling joists are structure.
- Engineer. Dindas says its span tables do not replace engineering advice, and anything outside the guide's assumptions needs a project-specific design. It says notches and holes must follow AS 1684.2 Clause 4.1.6, and anything beyond that is outside its guide and goes to an engineer.
- Approval. The City of Gold Coast says minor repairs that do not affect the structural or fire safety of a building may not need approval. Changing joists or taking out a wall that holds them up affects the structure, so plan on building approval.
- Licence. The QBCC says building work over $3,300 needs a QBCC licence. Its carpentry licence class covers erecting ceiling and subfloor framing.
Cutting a joist for a roof hatch is structural work too. Our guide to attic ladder installation covers that job.
We do the framing inside our kitchen, bathroom and laundry renovations across the Gold Coast, and we build to the engineer's design. We do not size joists or beams: the span table or the engineer does. Brett holds QBCC licence 15316127. See our carpentry page for the work we do.
Where do these figures come from?
Checked on 16 November 2026: Dindas Australia, LVL span tables page and its LVL 13.2 Span Tables Design Guide (2025); Gyprock, The Red Book 2 Residential Installation Guide (May 2020); Wesbeam, e-beam product page (undated); Hyne Timber, Common product span tables page (undated); Standards Australia store, AS 1684.2 N3 Supplement 4 (listed as current); City of Gold Coast, Do your building works need approval (undated); and the QBCC pages on who must hold a licence (last reviewed 11 August 2021) and the carpentry licence class (last reviewed 30 August 2021). We will check these figures again every three months.
See our carpentry work, or check what your job will cost.



